1. U-Boot SPL 2017.01-2 (Jan 18 2017 - 21:24:24)

  2. DRAM: 512 MiB

  3. CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2

  4. Trying to boot from MMC1

  5. 

  6. U-Boot 2017.01-2 (Jan 18 2017 - 21:24:24 -0700) Arch Linux ARM

  7. 

  8. CPU:   Allwinner A13 (SUN5I)

  9. Model: Olimex A13-Olinuxino

  10. I2C:   ready

  11. DRAM:  512 MiB

  12. MMC:   SUNXI SD/MMC: 0

  13. *** Warning - bad CRC, using default environment

  14. 

  15. Setting up a 1024x768 vga console (overscan 0x0)

  16. In:    serial

  17. Out:   vga

  18. Err:   vga

  19. Net:   No ethernet found.

  20. starting USB...

  21. USB0:   USB EHCI 1.00

  22. USB1:   USB OHCI 1.0

  23. scanning bus 0 for devices... 2 USB Device(s) found

  24. Hit any key to stop autoboot:  2  1  0 

  25. switch to partitions #0, OK

  26. mmc0 is current device

  27. Scanning mmc 0:1...

  28. Found U-Boot script /boot.scr

  29. 725 bytes read in 260 ms (2 KiB/s)

  30. ## Executing script at 43100000

  31. 5727976 bytes read in 574 ms (9.5 MiB/s)

  32. 30978 bytes read in 4661 ms (5.9 KiB/s)

  33. 4225001 bytes read in 464 ms (8.7 MiB/s)

  34. ## Flattened Device Tree blob at 43000000

  35.    Booting using the fdt blob at 0x43000000

  36.    Loading Ramdisk to 49bf8000, end 49fff7e9 ... OK

  37.    Loading Device Tree to 49bed000, end 49bf7901 ... OK

  38. 

  39. Starting kernel ...

  40. 

  41. [    0.000000] Booting Linux on physical CPU 0x0

  42. [    0.000000] Linux version 4.10.8-1-ARCH (builduser@leming) (gcc version 6.3.1 20170306 (GCC) ) #1 SMP Sat Apr 1 11:17:20 MDT 2017

  43. [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d

  44. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

  45. [    0.000000] OF: fdt:Machine model: Olimex A13-Olinuxino

  46. [    0.000000] cma: Reserved 48 MiB at 0x5c800000

  47. [    0.000000] Memory policy: Data cache writeback

  48. [    0.000000] CPU: All CPU(s) started in SVC mode.

  49. [    0.000000] percpu: Embedded 14 pages/cpu @df83c000 s27340 r8192 d21812 u57344

  50. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129158

  51. [    0.000000] Kernel command line: console=ttyS0,115200 root=PARTUUID=46d44c64-01 rw rootwait

  52. [    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

  53. [    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

  54. [    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

  55. [    0.000000] Memory: 443280K/521216K available (11264K kernel code, 955K rwdata, 4424K rodata, 1024K init, 968K bss, 28784K reserved, 49152K cma-reserved, 0K highmem)

  56. [    0.000000] Virtual kernel memory layout:

  57. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

  58. [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)

  59. [    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)

  60. [    0.000000]     lowmem  : 0xc0000000 - 0xdfd00000   ( 509 MB)

  61. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)

  62. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)

  63. [    0.000000]       .text : 0xc0008000 - 0xc0c00000   (12256 kB)

  64. [    0.000000]       .init : 0xc1100000 - 0xc1200000   (1024 kB)

  65. [    0.000000]       .data : 0xc1200000 - 0xc12eef98   ( 956 kB)

  66. [    0.000000]        .bss : 0xc12f0000 - 0xc13e2388   ( 969 kB)

  67. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

  68. [    0.000000] Hierarchical RCU implementation.

  69. [    0.000000] 	Build-time adjustment of leaf fanout to 32.

  70. [    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.

  71. [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1

  72. [    0.000000] NR_IRQS:16 nr_irqs:16 16

  73. [    0.000025] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns

  74. [    0.000052] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns

  75. [    0.000412] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns

  76. [    0.001080] Console: colour dummy device 80x30

  77. [    0.001117] Calibrating delay loop... 1001.47 BogoMIPS (lpj=2002944)

  78. [    0.048108] pid_max: default: 32768 minimum: 301

  79. [    0.048347] Security Framework initialized

  80. [    0.048543] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

  81. [    0.048553] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

  82. [    0.049458] CPU: Testing write buffer coherency: ok

  83. [    0.049900] CPU0: thread -1, cpu 0, socket -1, mpidr 0

  84. [    0.050313] Setting up static identity map for 0x40100000 - 0x40100098

  85. [    0.052798] smp: Bringing up secondary CPUs ...

  86. [    0.052818] smp: Brought up 1 node, 1 CPU

  87. [    0.052827] SMP: Total of 1 processors activated (1001.47 BogoMIPS).

  88. [    0.052834] CPU: All CPU(s) started in SVC mode.

  89. [    0.054408] devtmpfs: initialized

  90. [    0.063073] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

  91. [    0.063505] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns

  92. [    0.063529] futex hash table entries: 256 (order: 2, 16384 bytes)

  93. [    0.067001] xor: measuring software checksum speed

  94. [    0.104103]    arm4regs  :  1238.000 MB/sec

  95. [    0.144094]    8regs     :  1109.000 MB/sec

  96. [    0.184097]    32regs    :  1107.000 MB/sec

  97. [    0.224097]    neon      :  1808.000 MB/sec

  98. [    0.224105] xor: using function: neon (1808.000 MB/sec)

  99. [    0.224298] pinctrl core: initialized pinctrl subsystem

  100. [    0.226114] NET: Registered protocol family 16

  101. [    0.228482] DMA: preallocated 256 KiB pool for atomic coherent allocations

  102. [    0.230389] cpuidle: using governor menu

  103. [    0.230990] No ATAGs?

  104. [    0.230998] hw-breakpoint: debug architecture 0x4 unsupported.

  105. [    0.231803] Serial: AMBA PL011 UART driver

  106. [    0.316134] raid6: int32x1  gen()   238 MB/s

  107. [    0.384142] raid6: int32x1  xor()   232 MB/s

  108. [    0.452173] raid6: int32x2  gen()   345 MB/s

  109. [    0.520144] raid6: int32x2  xor()   280 MB/s

  110. [    0.588173] raid6: int32x4  gen()   331 MB/s

  111. [    0.656185] raid6: int32x4  xor()   261 MB/s

  112. [    0.724227] raid6: int32x8  gen()   332 MB/s

  113. [    0.792130] raid6: int32x8  xor()   240 MB/s

  114. [    0.860114] raid6: neonx1   gen()  1463 MB/s

  115. [    0.928117] raid6: neonx1   xor()   854 MB/s

  116. [    0.996126] raid6: neonx2   gen()  1937 MB/s

  117. [    1.024101] random: fast init done

  118. [    1.064107] raid6: neonx2   xor()  1219 MB/s

  119. [    1.132133] raid6: neonx4   gen()  1207 MB/s

  120. [    1.200120] raid6: neonx4   xor()   895 MB/s

  121. [    1.268149] raid6: neonx8   gen()   874 MB/s

  122. [    1.336136] raid6: neonx8   xor()   792 MB/s

  123. [    1.336143] raid6: using algorithm neonx2 gen() 1937 MB/s

  124. [    1.336149] raid6: .... xor() 1219 MB/s, rmw enabled

  125. [    1.336156] raid6: using intx1 recovery algorithm

  126. [    1.337785] reg-fixed-voltage usb0-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb0_vbus_pin@0, deferring probe

  127. [    1.337832] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe

  128. [    1.341378] vgaarb: loaded

  129. [    1.342232] SCSI subsystem initialized

  130. [    1.342861] usbcore: registered new interface driver usbfs

  131. [    1.342938] usbcore: registered new interface driver hub

  132. [    1.343031] usbcore: registered new device driver usb

  133. [    1.343965] Linux cec interface: v0.10

  134. [    1.344015] media: Linux media interface: v0.10

  135. [    1.344060] Linux video capture interface: v2.00

  136. [    1.344228] pps_core: LinuxPPS API ver. 1 registered

  137. [    1.344235] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>

  138. [    1.344258] PTP clock support registered

  139. [    1.344296] EDAC MC: Ver: 3.0.0

  140. [    1.345416] Advanced Linux Sound Architecture Driver Initialized.

  141. [    1.346088] NetLabel: Initializing

  142. [    1.346099] NetLabel:  domain hash size = 128

  143. [    1.346104] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO

  144. [    1.346179] NetLabel:  unlabeled traffic allowed by default

  145. [    1.346647] clocksource: Switched to clocksource timer

  146. [    1.346866] VFS: Disk quotas dquot_6.6.0

  147. [    1.346948] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

  148. [    1.348236] simple-framebuffer 5fd00000.framebuffer: framebuffer at 0x5fd00000, 0x300000 bytes, mapped to 0xe0080000

  149. [    1.348254] simple-framebuffer 5fd00000.framebuffer: format=x8r8g8b8, mode=1024x768x32, linelength=4096

  150. [    1.360577] Console: switching to colour frame buffer device 128x48

  151. [    1.370968] simple-framebuffer 5fd00000.framebuffer: fb0: simplefb registered!

  152. [    1.381346] NET: Registered protocol family 2

  153. [    1.382154] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

  154. [    1.382202] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

  155. [    1.382263] TCP: Hash tables configured (established 4096 bind 4096)

  156. [    1.382342] UDP hash table entries: 256 (order: 1, 8192 bytes)

  157. [    1.382363] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

  158. [    1.382546] NET: Registered protocol family 1

  159. [    1.383153] RPC: Registered named UNIX socket transport module.

  160. [    1.383169] RPC: Registered udp transport module.

  161. [    1.383175] RPC: Registered tcp transport module.

  162. [    1.383181] RPC: Registered tcp NFSv4.1 backchannel transport module.

  163. [    1.383749] Unpacking initramfs...

  164. [    1.660028] Freeing initrd memory: 4128K

  165. [    1.663445] workingset: timestamp_bits=14 max_order=17 bucket_order=3

  166. [    1.669713] zbud: loaded

  167. [    1.673004] NFS: Registering the id_resolver key type

  168. [    1.673052] Key type id_resolver registered

  169. [    1.673059] Key type id_legacy registered

  170. [    1.673076] nfs4filelayout_init: NFSv4 File Layout Driver Registering...

  171. [    1.681026] Key type asymmetric registered

  172. [    1.681315] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)

  173. [    1.681545] io scheduler noop registered

  174. [    1.681556] io scheduler deadline registered

  175. [    1.681772] io scheduler cfq registered (default)

  176. [    1.683691] sun4i-usb-phy 1c13400.phy: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb0_id_detect_pin@0, deferring probe

  177. [    1.688909] sun5i-a13-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver

  178. [    1.705433] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled

  179. [    1.708444] console [ttyS0] disabled

  180. [    1.728590] 1c28400.serial: ttyS0 at MMIO 0x1c28400 (irq = 26, base_baud = 1500000) is a U6_16550A

  181. [    2.515148] console [ttyS0] enabled

  182. [    2.519536] Serial: AMBA driver

  183. [    2.523705] [drm] Initialized

  184. [    2.535561] loop: module loaded

  185. [    2.540222] Loading iSCSI transport class v2.0-870.

  186. [    2.545702] iscsi: registered transport (tcp)

  187. [    2.553634] libphy: Fixed MDIO Bus: probed

  188. [    2.560491] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

  189. [    2.567074] ehci-pci: EHCI PCI platform driver

  190. [    2.571591] ehci-platform: EHCI generic platform driver

  191. [    2.577129] ehci-mxc: Freescale On-Chip EHCI Host driver

  192. [    2.582563] ehci-omap: OMAP-EHCI Host Controller driver

  193. [    2.588037] ehci-orion: EHCI orion driver

  194. [    2.592185] ehci-exynos: EHCI EXYNOS driver

  195. [    2.596490] tegra-ehci: Tegra EHCI driver

  196. [    2.600615] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

  197. [    2.606850] ohci-pci: OHCI PCI platform driver

  198. [    2.611379] ohci-platform: OHCI generic platform driver

  199. [    2.616844] ohci-exynos: OHCI EXYNOS driver

  200. [    2.621196] ohci-omap3: OHCI OMAP3 driver

  201. [    2.625619] usbcore: registered new interface driver uas

  202. [    2.631022] usbcore: registered new interface driver usb-storage

  203. [    2.637077] usbcore: registered new interface driver ums-cypress

  204. [    2.643140] usbcore: registered new interface driver ums_eneub6250

  205. [    2.649367] usbcore: registered new interface driver ums-freecom

  206. [    2.655417] usbcore: registered new interface driver ums-isd200

  207. [    2.661375] usbcore: registered new interface driver ums-usbat

  208. [    2.671594] i2c /dev entries driver

  209. [    2.676876] axp20x-i2c 0-0034: AXP20x variant AXP209 found

  210. [    2.690871] axp20x-regulator axp20x-regulator: regulators node not found

  211. [    2.702140] axp20x-i2c 0-0034: AXP20X driver loaded

  212. [    2.715115] sdhci: Secure Digital Host Controller Interface driver

  213. [    2.721338] sdhci: Copyright(c) Pierre Ossman

  214. [    2.726509] Synopsys Designware Multimedia Card Interface Driver

  215. [    2.733069] VUB300 Driver rom wait states = 1C irqpoll timeout = 0400

  216. [    2.733694] usbcore: registered new interface driver vub300

  217. [    2.745876] usbcore: registered new interface driver ushc

  218. [    2.752783] sunxi-mmc 1c0f000.mmc: Got CD GPIO

  219. [    2.794920] sunxi-mmc 1c0f000.mmc: base:0xe03ac000 irq:19

  220. [    2.800845] sdhci-pltfm: SDHCI platform and OF driver helper

  221. [    2.811635] ledtrig-cpu: registered to indicate activity on CPUs

  222. [    2.817951] hidraw: raw HID events driver (C) Jiri Kosina

  223. [    2.823835] usbcore: registered new interface driver usbhid

  224. [    2.829466] usbhid: USB HID core driver

  225. [    2.833656] ashmem: initialized

  226. [    2.844811] NET: Registered protocol family 10

  227. [    2.871737] mmc0: host does not support reading read-only switch, assuming write-enable

  228. [    2.884871] Segment Routing with IPv6

  229. [    2.888934] mmc0: new high speed SDHC card at address 0007

  230. [    2.894621] mip6: Mobile IPv6

  231. [    2.897729] NET: Registered protocol family 17

  232. [    2.903267] Key type dns_resolver registered

  233. [    2.907753] ThumbEE CPU extension supported.

  234. [    2.912140] mmcblk0: mmc0:0007 SD8GB 7.42 GiB 

  235. [    2.917435] Registering SWP/SWPB emulation handler

  236. [    2.922481]  mmcblk0: p1

  237. [    2.926773] registered taskstats version 1

  238. [    2.931039] zswap: loaded using pool lzo/zbud

  239. [    2.937798] Btrfs loaded, crc32c=crc32c-generic

  240. [    2.951881] ehci-platform 1c14000.usb: EHCI Host Controller

  241. [    2.957567] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1

  242. [    2.965617] ehci-platform 1c14000.usb: irq 21, io mem 0x01c14000

  243. [    2.986691] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00

  244. [    2.993062] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

  245. [    2.999886] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

  246. [    3.007121] usb usb1: Product: EHCI Host Controller

  247. [    3.012008] usb usb1: Manufacturer: Linux 4.10.8-1-ARCH ehci_hcd

  248. [    3.018018] usb usb1: SerialNumber: 1c14000.usb

  249. [    3.023384] hub 1-0:1.0: USB hub found

  250. [    3.027279] hub 1-0:1.0: 1 port detected

  251. [    3.032916] ohci-platform 1c14400.usb: Generic Platform OHCI controller

  252. [    3.039729] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 2

  253. [    3.047767] ohci-platform 1c14400.usb: irq 22, io mem 0x01c14400

  254. [    3.114893] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001

  255. [    3.121705] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

  256. [    3.128934] usb usb2: Product: Generic Platform OHCI controller

  257. [    3.134865] usb usb2: Manufacturer: Linux 4.10.8-1-ARCH ohci_hcd

  258. [    3.140878] usb usb2: SerialNumber: 1c14400.usb

  259. [    3.146219] hub 2-0:1.0: USB hub found

  260. [    3.150102] hub 2-0:1.0: 1 port detected

  261. [    3.156020] usb_phy_generic.0.auto supply vcc not found, using dummy regulator

  262. [    3.164128] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver

  263. [    3.169950] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3

  264. [    3.178027] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002

  265. [    3.184840] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1

  266. [    3.192067] usb usb3: Product: MUSB HDRC host driver

  267. [    3.197038] usb usb3: Manufacturer: Linux 4.10.8-1-ARCH musb-hcd

  268. [    3.203059] usb usb3: SerialNumber: musb-hdrc.1.auto

  269. [    3.208798] hub 3-0:1.0: USB hub found

  270. [    3.212674] hub 3-0:1.0: 1 port detected

  271. [    3.218179] hctosys: unable to open rtc device (rtc0)

  272. [    3.223340] sr_init: No PMIC hook to init smartreflex

  273. [    3.228774] sr_init: platform driver register failed for SR

  274. [    3.234767] vcc3v0: disabling

  275. [    3.237740] vcc5v0: disabling

  276. [    3.240739] usb0-vbus: disabling

  277. [    3.243983] ALSA device list:

  278. [    3.246959]   No soundcards found.

  279. [    3.252332] Freeing unused kernel memory: 1024K

  280. :: running early hook [udev]

  281. Warning: /lib/modules/4.10.8-1-ARCH/modules.devname not found - ignoring

  282. starting version 232

  283. :: running hook [udev]

  284. :: Triggering uevents...

  285. [    3.450782] usb 1-1: new high-speed USB device number 2 using ehci-platform

  286. [    3.616968] usb 1-1: New USB device found, idVendor=0bda, idProduct=8176

  287. [    3.623784] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3

  288. [    3.630937] usb 1-1: Product: 802.11n WLAN Adapter

  289. [    3.635746] usb 1-1: Manufacturer: Realtek

  290. [    3.639857] usb 1-1: SerialNumber: 00e04c000001

  291. :: performing fsck on '/dev/mmcblk0p1'

  292. /dev/mmcblk0p1: clean, 35152/486720 files, 254653/1945344 blocks

  293. :: mounting '/dev/mmcblk0p1' on real root

  294. [    6.240045] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)

  295. :: running cleanup hook [udev]

  296. [    6.735548] systemd[1]: System time before build time, advancing clock.

  297. [    6.814323] ip_tables: (C) 2000-2006 Netfilter Core Team

  298. [    6.880593] systemd[1]: systemd 232 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)

  299. [    6.899421] systemd[1]: Detected architecture arm.

  300. 

  301. Welcome to Arch Linux ARM!

  302. 

  303. [    6.916657] systemd[1]: Set hostname to <alarm>.

  304. [    7.133984] random: crng init done

  305. [    7.527815] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.

  306. [  OK  ] Started Dispatch Password Requests to Console Directory Watch.

  307. [    7.555249] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.

  308. [  OK  ] Listening on /dev/initctl Compatibility Named Pipe.

  309. [    7.575195] systemd[1]: Listening on Journal Socket (/dev/log).

  310. [  OK  ] Listening on Journal Socket (/dev/log).

  311. [    7.623069] systemd[1]: Listening on Journal Socket.

  312. [  OK  ] Listening on Journal Socket.

  313. [    7.641811] systemd[1]: Created slice System Slice.

  314. [  OK  ] Created slice System Slice.

  315. [    7.660241] systemd[1]: Created slice system-serial\x2dgetty.slice.

  316. [  OK  ] Created slice system-serial\x2dgetty.slice.

  317. [    7.684035] systemd[1]: Starting Create list of required static device nodes for the current kernel...

  318.          Starting Create list of required st…ce nodes for the current kernel...

  319.          Starting Journal Service...

  320. [  OK  ] Created slice system-getty.slice.

  321. [  OK  ] Listening on udev Kernel Socket.

  322. [  OK  ] Listening on Process Core Dump Socket.

  323. [  OK  ] Started Forward Password Requests to Wall Directory Watch.

  324. [  OK  ] Reached target Paths.

  325. [  OK  ] Listening on Device-mapper event daemon FIFOs.

  326.          Mounting Configuration File System...

  327.          Mounting Debug File System...

  328.          Starting Remount Root and Kernel File Systems...

  329. [  OK  ] Reached target Encrypted Volumes.

  330. [  OK  ] Listening on LVM2 metadata daemon socket.

  331. [  OK  ] Listening on Network Service Netlink Socket.

  332.          Starting Apply Kernel Variables...

  333. [  OK  ] Created slice User and Session Slice.

  334. [  OK  ] Reached target Remote File Systems.

  335.          Mounting POSIX Message Queue File System...

  336. [  OK  ] Reached target Slices.

  337. [  OK  ] Listening on udev Control Socket.

  338. [  OK  ] Set up automount Arbitrary Executab…rmats File System Automount Point.

  339. [  OK  ] Reached target Swap.

  340.          Mounting Temporary Directory...

  341. [  OK  ] Mounted Debug File System.

  342. [  OK  ] Mounted POSIX Message Queue File System.

  343. [  OK  ] Mounted Configuration File System.

  344. [  OK  ] Mounted Temporary Directory.

  345. [  OK  ] Started Create list of required sta…vice nodes for the current kernel.

  346. [  OK  ] Started Remount Root and Kernel File Systems.

  347. [  OK  ] Started Apply Kernel Variables.

  348.          Starting udev Coldplug all Devices...

  349.          Starting Load/Save Random Seed...

  350.          Starting Create System Users...

  351. [  OK  ] Started Journal Service.

  352.          Starting Flush Journal to Persistent Storage...

  353. [  OK  ] Started Load/Save Random Seed.

  354. [  OK  ] Started Create System Users.

  355.          Starting Create Static Device Nodes in /dev...

  356. [    9.115488] systemd-journald[156]: Received request to flush runtime journal from PID 1

  357. [  OK  ] Started Flush Journal to Persistent Storage.

  358. [  OK  ] Started Create Static Device Nodes in /dev.

  359.          Starting udev Kernel Device Manager...

  360. [  OK  ] Reached target Local File Systems (Pre).

  361. [  OK  ] Reached target Local File Systems.

  362.          Starting Rebuild Dynamic Linker Cache...

  363.          Starting Rebuild Journal Catalog...

  364.          Starting Create Volatile Files and Directories...

  365. [  OK  ] Started Rebuild Journal Catalog.

  366. [  OK  ] Started udev Kernel Device Manager.

  367. [  OK  ] Started udev Coldplug all Devices.

  368. [  OK  ] Started Create Volatile Files and Directories.

  369.          Starting Update UTMP about System Boot/Shutdown...

  370.          Starting Network Time Synchronization...

  371. [  OK  ] Started Update UTMP about System Boot/Shutdown.

  372. [  OK  ] Started Network Time Synchronization.

  373. [  OK  ] Reached target System Time Synchronized.

  374. [  OK  ] Started Rebuild Dynamic Linker Cache.

  375.          Starting Update is Completed...

  376. [  OK  ] Started Update is Completed.

  377. [  OK  ] Reached target System Initialization.

  378. [  OK  ] Started Daily verification of password and group files.

  379. [  OK  ] Started Daily man-db cache update.

  380. [  OK  ] Listening on D-Bus System Message Bus Socket.

  381. [  OK  ] Reached target Sockets.

  382. [  OK  ] Reached target Basic System.

  383.          Starting SSH Key Generation...

  384. [  OK  ] Started Entropy Harvesting Daemon.

  385.          Starting Login Service...

  386. [  OK  ] Started D-Bus System Message Bus.

  387. [   12.497977] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

  388. [   12.504752] [drm] No driver support for vblank timestamp query.

  389.          Starting Network Service...

  390. [  OK  ] Started Daily rotation of log files.

  391. [  OK  ] Started Daily Cleanup of Temporary Directories.

  392. [  OK  ] Reached target Timers.

  393. [  OK  ] Started Login Service.

  394. [  OK  ] Started Network Service.

  395. [  OK  ] Reached target Network.

  396.          Starting Network Name Resolution...

  397.          Starting Permit User Sessions...

  398. [  OK  ] Started Permit User Sessions.

  399. [  OK  ] Started Getty on tty1.

  400. [   13.215361] sun4i-drm display-engine: bound 1e60000.display-backend (ops sun4i_backend_ops [sun4i_backend])

  401. [  OK  ] Started Network Name Resolution.

  402. [   13.467519] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_ops [sun4i_tcon])

  403. [   13.657962] fb: switching to sun4i-drm-fb from simple

  404. [   13.782858] Console: switching to colour dummy device 80x30

  405. [   14.297069] input: 1c22800.lradc as /devices/platform/soc@01c00000/1c22800.lradc/input/input0

  406. [   14.338880] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=1)

  407. [   14.475396] Console: switching to colour frame buffer device 128x48

  408. [   15.223747] sun4i-drm display-engine: fb0:  frame buffer device

  409. [  OK  ] Found device /dev/ttyS0.

  410. [   15.266595] input: axp20x-pek as /devices/platform/soc@01c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input1

  411. [  OK  ] Started Serial Getty on ttyS0.

  412. [  OK  ] Reached target Login Prompts.

  413. [   16.598738] rtl8192cu: Chip version 0x10

  414. [  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.

  415. [   17.312240] rtl8192cu: Board Type 0

  416. [   17.339093] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1

  417. [   17.354784] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin

  418.          Starting Load/Save RF Kill Switch Status...

  419. [   17.503243] usbcore: registered new interface driver rtl8192cu

  420. [  OK  ] Started Load/Save RF Kill Switch Status.

  421. 

  422. Arch Linux 4.10.8-1-ARCH (ttyS0)

  423. 

  424. alarm login: root

  425. Password: 

  426. [root@alarm ~]# iwco    lsmod

  427. Module                  Size  Used by

  428. arc4                    1943  2

  429. evdev                  12667  0

  430. rtl8192cu              60903  0

  431. rtl_usb                10054  1 rtl8192cu

  432. rtl8192c_common        41686  1 rtl8192cu

  433. rtlwifi                61334  3 rtl_usb,rtl8192c_common,rtl8192cu

  434. mac80211              422312  3 rtl_usb,rtlwifi,rtl8192cu

  435. cfg80211              258941  2 mac80211,rtlwifi

  436. sun4i_ts                4456  0

  437. axp20x_pek              3651  0

  438. rfkill                 18763  2 cfg80211

  439. sun4i_gpadc             3745  0

  440. sun4i_lradc_keys        3478  0

  441. sunxi_wdt               3769  0

  442. sun4i_drm               9356  0

  443. sun4i_tcon             14395  1 sun4i_drm

  444. sun4i_backend           8642  1 sun4i_drm

  445. dumb_vga_dac            3423  0

  446. uio_pdrv_genirq         3591  0

  447. uio                     9202  1 uio_pdrv_genirq

  448. sch_fq_codel            9096  1

  449. ip_tables              12756  0

  450. x_tables               18255  1 ip_tables

  451. [root@alarm ~]# ls -la /dev/block  

  452. total 0

  453. drwxr-xr-x  2 root root  240 Jan  1  1970 .

  454. drwxr-xr-x 14 root root 3040 Feb  1 01:10 ..

  455. lrwxrwxrwx  1 root root   10 Feb  1 01:10 179:0 -> ../mmcblk0

  456. lrwxrwxrwx  1 root root   12 Feb  1 01:10 179:1 -> ../mmcblk0p1

  457. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:0 -> ../loop0

  458. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:1 -> ../loop1

  459. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:2 -> ../loop2

  460. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:3 -> ../loop3

  461. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:4 -> ../loop4

  462. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:5 -> ../loop5

  463. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:6 -> ../loop6

  464. lrwxrwxrwx  1 root root    8 Feb  1 01:10 7:7 -> ../loop7

  465. [root@alarm ~]# uname -a

  466. Linux alarm 4.10.8-1-ARCH #1 SMP Sat Apr 1 11:17:20 MDT 2017 armv7l GNU/Linux